The bad news: We had to get hauled out this week.
The good news: We’re back in the water and finally on our way to Eleuthera tomorrow!
So here’s what happened. After slowly traversing the Abacos from north to south, we had finally made our way down to Little Harbor, our gateway to cross to Eleuthera. With the boat safely anchored, Aaron donned his snorkel gear and dove down to clear what we thought was a clogged water inlet for our watermaker (turns out it was just an air lock in a pump which, once found, was fixed in seconds). But while he was down there, he noticed that our sacrificial anodes, or zincs, were in bad shape. The one on our propeller had fallen off (the bottom cleaner we hired in Florida installed it for us and apparently didn’t bolt it on correctly) and the one on our saildrive was just about shot.
We had another propeller anode on board and Aaron was able to do a quick replacement. The saildrive anode, however, was another story. We didn’t have a replacement on board – a definite oversight. And, to boot, replacing it meant disassembling the propeller and reassembling it. Newer saildrives allow zinc replacement without removing the prop… what a concept! Some props simply come off in one piece, but of course, we have a fancy, feathering propeller that folds up when we’re sailing to reduce drag. Great, except that to remove it, it has to be taken apart in many pieces (see photo). Not something easily done under water with scuba gear – at least, not the first time, which it would be for us.
For those who are unfamiliar, sacrificial anodes are pieces of zinc, a less noble metal, that stray electrical currents slowly eat away at, rather than the propeller, saildrive, or other underwater metal parts of the boat. They can originate in a number of ways – either from neighboring boats in a marina, or from an electrical issue on your boat. Aaron figures it was a combination of other boats in marinas back in the States, as well as an electrical issue of our own that he found and fixed during our first month on the boat this summer.
The anodes are very, very important and replacing them is just a matter of routine maintenance, not an issue of the boat malfunctioning. He had been keeping an eye on the propeller anode and had it replaced shortly before leaving the States. However, this being our first boat with a saildrive, we didn’t realize there was another anode for it. It should have been changed back in the States as well.
So there we were, perfectly positioned to head to Eleuthera the next day, and we had to make a decision. We could cross – the anodes needed attention, but we would be okay for another few weeks or more. But, Eleuthera is even more remote than the Abacos. We started frantically researching how we might get the anodes shipped there, and though there seemed to be a few possibilities, they were questionable at best, and definitely wouldn’t be speedy.
The bigger problem, though, was that there aren’t any yacht yards in the Eleuthera island chain that could haul out the boat. So, either we swallowed our pride, turned the boat around and stayed in the Abacos to get the boat hauled, or we continued on and either got the parts shipped somewhere in Eleuthera and did all the work underwater in scuba gear (don’t drop anything!), or hoped the old anode held up long enough to get to Georgetown in the Exumas and got hauled out there. Honestly, we were extremely lucky that Aaron noticed the problem the day before we left, when we were still in a place that afforded us some options. It’s amazing how a $20 part can bring everything to a halt.
After a day of letting the bad news sink in, we bit the bullet and ordered the anodes to be delivered to Marsh Harbor, as we had done with the engine shift/throttle mechanism a month or so ago. We called the Marsh Harbor Boat Yard and got on their schedule for a haul out the soonest they had an opening, a week later. And we tried to make the most of the time in between. It’s all just time and money, right? A lot of both.
Ultimately, it all turned out fine. Sure, there were hiccups. Our package was delayed clearing customs, which pushed us back a day. And the delay meant that we missed our window for a short-haul of just a few hours to replace the anodes, and instead had to be fully hauled out and blocked for a night. But, we also rented a car in Marsh Harbor to maximize our time. We did a big provisioning run, filled our propane tanks, got diesel for the boat, stopped at the bank, made a few trips to the hardware store, and even managed to get a few birthday presents for Claire. Her birthday is at the end of March, and toy stores and Amazon shipments just don’t exist here, especially not where we’re headed. Marsh Harbor was our best bet, and luckily, I found just what I was looking for – a kickboard.
Aaron also put in two grueling days of hard manual labor, taking advantage of the boat being out of the water to take care of as many things as possible in addition to the anodes, like cleaning the bottom of the boat, resealing and cleaning out some throughhull fittings, fixing our underwater speed sensor, reinstalling the rubber fairing around the saildrive (lots of sanding and gluing), and overseeing some workers fixing our broken window and changing the oil in the saildrive (it has to be drained out and pumped in from the bottom).
The boat was hauled on Wednesday midday and was back in the water 24 hours later. By mid-afternoon Thursday, we dropped anchor again in Little Harbor, where it all started. And tomorrow, we will cross the Atlantic 65 miles to Eleuthera – with two new anodes in place, and two spares of each on board.
While Aaron was taking a break from working on the boat, he walked across the yacht yard to several men working on a beautiful catamaran. Feeling somewhat gloomy, he thought, “If we could only afford something like that, we wouldn’t be fixing stuff all the time.” The boat is two years old and valued at roughly $550,000. What could they possibly be fixing on such a new, expensive boat?
Both rudder shafts were apparently cast with inferior steel and had swelled in place. The result: The owners were barely able to steer the boat. It was hauled out and had been there for quite some time while new parts were made, others were ordered from France, and many, many hours of hired labor were put in to tear apart and rebuild the steering system. Someone’s cruising plans had not just been delayed, but completely canceled.
We will always have problems to fix, parts to replace, and maintenance chores to do, as this boat is many times more complex than our previous one. Weather conditions will delay plans, freak medical conditions will pop up. The lesson here is to not let these things kill your spirit. I think we’re getting better and better at that.